Buying Guides
C7 Ball Screw Accuracy Explained: Is ±0.05mm/300mm Good Enough for Your CNC?
C7 ball screw accuracy is typically ±0.05mm per 300mm. Learn what that means for CNC, automation and 3D printers, when C7 is enough, and when you need C5.
C7 Ball Screw Accuracy Explained: Is ±0.05mm/300mm Good Enough for Your CNC?
If you are buying a ball screw for a CNC machine, an automation axis, or a 3D printer, you have probably seen this question in every quote: C3, C5, C7, or C10?
Most buyers do not need the most accurate screw. They need the screw that is accurate enough — without paying for precision they will never use.
That is why C7 is our core business at Weimute. This article explains what C7 accuracy really means, in plain language, so you can decide with confidence.
What does C7 mean?
Ball screw accuracy grades follow the JIS standard. The grade tells you how far the actual travel can deviate from the ideal travel over a given length.
Typical lead accuracy values used in the industry are:
These are the variation within any 300 mm length (JIS B 1192). The representative travel error over the full screw length is larger and grows with length — ask for the value for your exact length.
C7 is a rolled ball screw grade. Rolling is faster and more cost-effective than grinding, which is why C7 gives you a very good balance of accuracy and price.
A C7 screw does not mean the error is always 0.05 mm. It means the lead error stays within that band over 300 mm of travel under standard conditions. For many machines, that is more than enough.
The pain point: "Will C7 be accurate enough for my machine?"
This is the question we hear most from buyers. It usually comes from one of three worries:
- "My parts are out of tolerance." The screw is often blamed first, but the cause is often backlash, poor alignment, a loose coupling, or a worn support bearing. A C7 screw with correct preload, alignment, and supports will hold position far better than a higher-grade screw installed badly.
- "I was quoted C5, but C7 is half the price. Is it a trap?" Not necessarily. If your drawing tolerance is ±0.05 mm or looser, and your repeatability requirement is in the 0.02–0.05 mm range, C7 is often the right economic choice. You pay for C5 when you need tighter lead accuracy across long travel — for example, precision grinding or long, high-accuracy positioning.
- "My supplier will not explain the grade." Ask for three things in every quote: the accuracy grade (C7), the lead error per 300 mm, and whether the nut is single or double. If a supplier cannot give you those three, do not buy on price alone.
When C7 is enough — and when it is not
C7 is usually a good fit for: General CNC routers, mills, and lathes; Automation axes, pick-and-place, and linear modules; 3D printers and laser equipment; Medical, food, and packaging machines where ±0.05 mm is acceptable; Any application where repeatability matters more than absolute lead accuracy over a very long stroke.
Consider C5 or C3 when: Your part tolerance is tighter than ±0.02 mm over the full travel; You need high accuracy over a stroke longer than 1,000 mm without compensation; You are building inspection, grinding, or semiconductor equipment.
If you are not sure, send us your travel length, load, speed, and tolerance. We will tell you honestly whether C7 is enough — even if the answer is to choose a higher grade.
How to get the best accuracy from a C7 screw
Accuracy is not only the grade on the label. These four things matter just as much:
- Choose the right diameter and lead. A larger diameter reduces deflection. A smaller lead gives finer resolution and higher thrust for the same motor torque. Our most popular C7 sizes are SFU1605, SFU1610, SFU2005, SFU2010, SFU2505, and SFU3205.
- Use the correct supports. A fixed end (BK / FK / EK) and a supported end (BF / FF / EF) keep the screw straight and stable. Do not skip the support to save cost.
- Check alignment during installation. Even a small misalignment adds friction, noise, and wear. The screw should turn smoothly by hand over the full travel before you run the motor.
- Lubricate and protect it. Keep chips and dust out, lubricate on schedule, and check backlash every few months. A well-maintained C7 screw lasts far longer than a neglected C5 screw.
What Weimute C7 ball screws offer
- Grades C5 / C7 / C10, with C7 as our main stock grade
- SFU single-nut and DFU double-nut types; most popular C7 sizes SFU1605, SFU1610, SFU2005, SFU2010, SFU2505 and SFU3205 (diameters 16–32 mm, leads 5–10 mm)
- Length 100–6,000 mm, custom end machining
- Material GCr15, left-hand and right-hand threads available
- ISO 9001:2015 and ISO 14001:2015
- Sample in about 7 working days, production in 15–20 working days, quote usually within 24 hours Our SFU1604, for example, is available in C5 / C7 / C10, with custom end machining for CNC automation machinery.
FAQ
Is C7 repeatability the same as accuracy? No. Accuracy is how close the travel is to the ideal. Repeatability is how consistently the nut returns to the same position. A good C7 screw can have excellent repeatability even if its absolute lead error is larger than C5.
Can I use a C7 screw for a 2-meter stroke? Yes, in many cases, but check critical speed and buckling first. Tell us the stroke, load, and speed and we will check the size for you.
What is the difference between C7 and C10? C10 has a larger lead error band and is mainly for transport and general positioning where precision is less critical. C7 is the standard choice when you need real positioning accuracy without ground-screw cost.
Get a quote
Tell us your diameter, lead, length, accuracy grade, and end machining. We will confirm whether C7 is right for your application and send a quote, usually within 24 hours.
Contact: May. Phone: +8615268772262. Email: Info@weemt.com. Address: No. 7, Lvyuan Road, Shuige Street, Liandu District, Lishui City, Zhejiang Province, China.
View our ball screws | Contact us | Get a Quote
