Buying Guides

How to Size a C7 Ball Screw: Diameter, Lead, Load and Critical Speed in 10 Minutes

Sizing a C7 ball screw wrong costs time, money, or accuracy. Learn how to pick diameter, lead, load capacity and critical speed in 10 minutes — with a worked example.

How to Size a C7 Ball Screw: Diameter, Lead, Load and Critical Speed in 10 Minutes

Most ball screw problems are not quality problems — they are sizing problems. A screw that is too thin whips at speed. A lead that is too fine makes the axis crawl. A nut rated for half the real load wears out in months. You can size a C7 ball screw correctly in about ten minutes, with five checks.

1. Start with the load, not the diameter

Everything starts with the axial load — the force pushing along the screw. Add up the weight of the moving parts, the cutting or working force, and the friction of the guides. Then multiply by a safety factor: a typical rule of thumb is 2–3 for reversing or shock loads, and about 1.5 for smooth, one-direction loads. These are typical industry practice, not a guarantee — check the rating of the exact model you buy. Check your result against the screw's dynamic load rating (Ca) in the supplier's catalog — your working load should sit well below it. If it does not, go up a size: a bigger diameter is almost always cheaper than a failed screw. One common mistake: sizing for the static load only. A screw that holds a load fine at rest can still fail early if the same load reverses thousands of times a day.

2. Pick the diameter — stiffness beats size

Diameter controls how much load the screw carries and how stiff it is. A stiffer screw deflects less under load, and deflection shows up directly as positioning error. Weimute's most popular C7 sizes are SFU1605–SFU3205 (16–32 mm diameter, leads 5–10 mm). As a rough guide:
Longer screws need bigger diameters: a 16 mm screw that is fine at 500 mm will flex and whip at 1,500 mm. When the span grows, step up the diameter.

3. Pick the lead — speed or force, not both

The lead is how far the nut travels in one turn of the screw. It is the simplest trade-off in sizing: a bigger lead gives more speed from the same motor speed, but less thrust force; a smaller lead gives more force, but slower travel. Linear speed is easy to work out: speed = lead × motor rpm. At 1,000 rpm:
For a CNC axis that needs fast rapids, a 10 mm lead is usually the better choice. For a Z-axis lifting a heavy spindle, or a press application, a 5 mm lead gives roughly twice the thrust from the same motor torque. Pick the lead for the job — 5 mm and 10 mm leads cost about the same, but the wrong one costs you performance.

4. Check critical speed — the limit buyers forget

Every screw has a critical speed: the rpm at which it starts to whip like a skipping rope. Run past it and you get vibration, noise, and rapid wear. Three things push critical speed down: a thinner screw, a longer screw, and a less rigid end support. The practical rule: keep your maximum operating speed below about 80% of the screw's critical speed. If your required speed is close to the limit, shorten the unsupported span, step up the diameter, or use a fixed-supported (BK / FK) end instead of a floating one. Ask your supplier to check it for your exact length and mounting.

5. Check the motor torque

Finally, make sure your motor can drive the screw: Torque (N·m) = axial load (N) × lead (m) ÷ (2π × efficiency) Ball screw efficiency is typically around 0.9. For example, moving a 1,000 N load with a 10 mm lead needs about 1.8 N·m — before friction and acceleration. Add 30–50% margin for acceleration and friction, and check the motor's torque curve at running speed, not just its rated torque.

A worked example

A small CNC router, X-axis, 800 mm travel, moving mass about 50 kg, cutting force about 300 N:
  • Load: roughly 800 N total, with a safety factor of 2 → size for ~1,600 N
  • Diameter: SFU2005 or SFU2010 — 20 mm is stiff enough at this length
  • Lead: 10 mm for fast rapids (10 m/min at 1,000 rpm)
  • Critical speed: check with the supplier — a 20 mm screw with fixed-supported ends is normally fine at this span
  • Torque: about 2.8 N·m at 1,600 N with a 10 mm lead, before margin

Sizing checklist

  • Do I know the real axial load, including cutting force and friction?
  • Have I applied a safety factor for reversing or shock loads?
  • Is the diameter right for the length and the stiffness I need?
  • Did I choose the lead for speed or force — whichever the job needs?
  • Is my top speed below 80% of the screw's critical speed?
  • Can the motor deliver the torque, with margin, at running speed?

What Weimute C7 ball screws offer

  • Grades C5 / C7 / C10, with C7 as our main stock grade; SFU single-nut and DFU double-nut types — most popular C7 sizes SFU1605–SFU3205 (16–32 mm, leads 5–10 mm)
  • Length 100–6,000 mm, custom end machining; material GCr15; ISO 9001:2015 and ISO 14001:2015
  • Sample in about 7 working days, production in 15–20 working days, quote usually within 24 hours Send us your load, travel, speed, and mounting length, and we will check the sizing for you before you order.

FAQ

What happens if I pick a C7 ball screw that is too small? It will still work — at first. But you will see more deflection, faster wear, and vibration at high speed, and the screw may fail well before its rated life. Sizing up one diameter is usually cheaper than replacing a screw. Is a bigger lead always better for speed? Only if the motor can deliver the torque. A 10 mm lead moves twice as fast at the same rpm, but needs roughly twice the torque for the same load. If the motor stalls, the faster lead is useless. Do I need to calculate critical speed myself? Not precisely. You need to know your screw length, diameter, and end support type, then ask the supplier to verify it. The important thing is to ask — critical speed is the sizing check most buyers skip.

Get a quote

Tell us your load, travel length, required speed, and mounting type. We will check diameter, lead, and critical speed, and send a quote, usually within 24 hours. Contact: May. Phone: +8615268772262. Email: Info@weemt.com. Address: No. 7, Lvyuan Road, Shuige Street, Liandu District, Lishui City, Zhejiang Province, China. View our ball screws | Contact us | Get a Quote

Read next

More from the journal

Keep readers moving through related announcements, stories, and field notes.