Buying Guides
Backlash: Why Your CNC Loses Position and How a C7 Ball Screw Fixes It
Backlash makes your CNC lose position on every direction change. Learn what causes ball screw backlash, how much is normal for a C7 screw, and how to fix or prevent it.
Backlash: Why Your CNC Loses Position and How a C7 Ball Screw Fixes It
Your CNC cuts a perfect circle in one direction — and an oval when it reverses. Parts measure fine on the first pass, then drift by a few hundredths on the second. The machine has not lost its calibration. It has backlash, the most common positioning problem we hear about — and one of the most misunderstood.
What is backlash?
Backlash is the small free movement between the screw and the nut when the direction of travel reverses. The motor turns, but the nut does not move yet — it first has to cross a tiny gap.
In a ball screw, that gap comes from the clearance between the balls and the raceways. A small amount of clearance is normal and even necessary: without it, the balls cannot roll freely. The problem starts when the clearance is too large, or grows with wear.
Typical axial clearance values used in the industry:
These are typical industry values, not a guarantee for any single screw. Ask your supplier for the axial clearance of the exact model you are buying.
The pain point: "My machine loses position when it changes direction"
Backlash shows up in very specific ways:
- Circles come out as ovals. The error appears exactly at the quadrant points, where one axis reverses direction.
- Parts are right on the first pass, wrong on the return. The tool cuts correctly in one direction, then shifts when it comes back.
- The DRO moves but the table does not. The readout counts motor steps, but the axis stays still for the first fraction of a turn after reversal. Before blaming the ball screw, check the rest of the drive chain — a loose coupling, a worn support bearing, or play in the linear guide can look exactly like screw backlash. A new screw will not fix a loose coupling.
Where backlash comes from
There are four main sources, and only one of them is the screw itself:
- Nut clearance. The gap between the balls and the raceways — the biggest factor, and the one you control by choosing the nut type and preload.
- Wear. A screw that has run dry, or with chips and dust in the raceway, wears faster. Backlash that was fine on day one can become a problem after a year.
- Support bearings. Axial play in the fixed-end bearing (BK / FK / EK) adds directly to the total. A cheap or worn support can undo the benefit of a good screw.
- Coupling and mounting. Any play between the motor shaft and the screw shaft shows up as lost motion at the tool. When you measure backlash, you are measuring the sum of all of these. Fixing only the screw and ignoring the supports is a common and expensive mistake.
How a C7 ball screw fixes it
A C7 ball screw does not eliminate backlash by itself — no screw does. What it gives you is a controlled starting point, and the right options to reduce it:
- Choose a preloaded nut. For reversing loads, a double nut (DFU type) with preload removes the axial clearance almost completely. A single nut (SFU type) with light preload is a good middle ground for general CNC work.
- Match the nut to the load. A light, reversing load needs preload more than a heavy, one-direction load does. Tell your supplier how the axis actually moves, not just the maximum load.
- Use proper fixed-end supports. A BK / FK / EK support with angular contact bearings holds the screw axially. Do not use a plain bearing at the fixed end and expect the screw to do the work.
- Keep it lubricated and clean. Most backlash growth is wear, and most wear is preventable. Lubricate on schedule and check backlash every few months. A well-chosen C7 screw with a preloaded nut holds reversal error well within the tolerance most general CNC work needs — without paying for a ground C5 screw. The grade (C7) controls lead accuracy; the nut and preload control backlash. They are different things, and you need both right.
A quick backlash checklist
Use this before you order, and again after installation:
- Do I know the axial clearance of the nut I am buying?
- Is the load reversing, or mostly one direction?
- Have I chosen single nut (SFU) or double nut (DFU) to match that load?
- Is the fixed-end support a proper BK / FK / EK unit with angular contact bearings?
- Is the coupling tight, with no play between motor and screw?
What Weimute C7 ball screws offer
- Grades C5 / C7 / C10, with C7 as our main stock grade; SFU single-nut and DFU double-nut types — most popular C7 sizes SFU1605–SFU3205 (16–32 mm, leads 5–10 mm)
- Length 100–6,000 mm, custom end machining; material GCr15; ISO 9001:2015 and ISO 14001:2015
- Sample in about 7 working days, production in 15–20 working days, quote usually within 24 hours Tell us whether your axis reverses under load, and we will recommend a single or double nut — and the right preload — for your application.
FAQ
How much backlash is normal for a C7 ball screw? It depends on the nut. A standard single nut typically has a small axial clearance (often around 0.02–0.05 mm in the industry), while a preloaded double nut is close to zero. The grade C7 describes lead accuracy, not backlash — so always ask for the nut clearance separately.
Can I adjust backlash on a ball screw I already have? Sometimes. A double nut can often be re-adjusted to restore preload, but a worn single nut usually needs replacement. If the screw raceway itself is worn, replacing the nut alone will not fix it.
Does software backlash compensation fix the problem? It hides it, partly. Most CNC controllers add extra pulses on reversal to compensate for a known backlash value. It works for light, consistent loads, but not for backlash that changes with load or wear. Fix the mechanics first, then use compensation for the remainder.
Get a quote
Tell us your diameter, lead, length, accuracy grade, and whether your axis reverses under load. We will confirm whether C7 is right for your application and send a quote, usually within 24 hours.
Contact: May. Phone: +8615268772262. Email: Info@weemt.com. Address: No. 7, Lvyuan Road, Shuige Street, Liandu District, Lishui City, Zhejiang Province, China.
View our ball screws | Contact us | Get a Quote
